Valor 555CFK Operations Instructions

MADRONA©2011, Miles Industries Ltd.Madrona Free Standing Direct-Vent Top or Rear Vent StoveMF28ILN (NG) / MF28ILP (LPG)Engine to be installed ONLY wit

10VentingTop / Rear OutletVent MaterialThis unit is shipped with a top outlet collar which is fi eld-convertible to rear outlet—see page 20 for details

11Snorkel required (min. 14” high) with horizontal run through the wall(no rise)VentingThrough wall (without vertical rise)Typical Venting ComponentsS

5 x 90º ELBOWS MAXIMUMRestrictor 75NORESTRICTORSExample 1NO INSTALLATIONNO INSTALLATIONV3Restrictor 502 4 6 8 10 12 14 16 18 2012VentingAllowable Vent

13VentingRestrictorsSOME INSTALLATIONS REQUIRE RESTRICTORS. For improved fl ame picture and performance, this unit is supplied with two different sets

14VentingKEY VENT TERMINAL LOCATIONS - MINIMUM DISTANCES MINIMUM CLEARANCE Inches CmA Clearance above grade, verandah, porch, deck or balcony 12 30B

15Installation PlanningFan (Blower)Venting Confi gurationGas Line RoutingConsider visibility of shut-off valve or step-down regulators, etc. when plann

16Appliance Preparation1. Rough-in the gas line and electrical wiring for a fan (if any).2. Decide where the stove should be positioned to avoid mov

17Appliance PreparationEngine DetailFlip the base upside-down. Place the engine on the base at its approximate fi nal position—see detail below. Center

18Appliance PreparationFit the pipe and connector supplied with the engine to the valve. Connect the gas line to the inlet pipe.3/8” gas line connecti

19Appliance PreparationFasten Thermal Switch to underside of burner module using 2 existing screwsOptional Fan (Blower)If the Circulating Fan Kit (blo

2The information contained in this installation manual is believed to be correct at the time of printing. Miles Industries Ltd. reserves the right to

20Appliance PreparationTop Spar1. Position the top spar on the side brackets located between the engine and the cast sides.2. Fix the spar with four

21ConnectorPipesUnionsSupply Line SizeSealantManual Shut-off Valve & UnionTest Pressures >1/2 psig (3.5kPa)Possible DamagesTest Pressures ≤1/2

Both front logs to rest slightly on the edge of the fi rebox window frame.1. Place the rear log centering it side to side in the fi rebox. Position for

4. Identify the right cross log; it has a hole under on of its end and it is the shortest cross log. Place it on the right pin located on the rear lo

24Window Refi ttingx 4To refi t the window, place it on the fi rebox frame and hold it in place while pushing and turning its fastening studs 90 degrees.

25Front & Top InstallationFront InstallationHook the cast front to the side brackets located between the engine and the cast sides.Cast frontHookD

26Top CastingPlace the top casting piece on the top of the stove ensuring the rear edge is fl ush with the rear edge of the cast side panels. Fill in t

27For your safety, this appliance is fi tted with a fl ame supervision device which will shut-off the gas supply if, for any reason, the pilot fl ame goe

28BatteriesOwner’s InformationInspect the vent terminal outdoors regularly to make sure that snow, trees, bushes, leaves, or other objects do not obst

29Remote Control OperationYour fi replace remote control helps you get the comfort, convenience and aesthetics you want from your gas fi replace. The re

3Table of ContentsSafety & Warning Information ...4Specifi cations ...

30TimeThe flame height can be adjusted in the following manners. In STANDBY mode,1. Press the (large flame) button to turn on the main burner.2.

31Timer Use this setting when you come in and want to enjoy a set temperature. 1. Select either the ☼TEMP MODE or the ☽TEMP MODE by briefly pressing

32OptionsApplianceCast StovesVentingFan (Blower)MF28ILN—Natural Gas InstallationsMF28ILP—Propane Gas InstallationsConversion KitsMFCS01—Madrona Stove

33Lighting InstructionsWARNING: If you do not follow these instructions exactly a ¿re or exSlosion Pay result causinJ SroSerty daPaJe Sersonal inMur

34Wiring DiagramOptional Wall Switch Kit 1265WSKConnectorRedYellowGV60 Wiring Diagram

35Venting AccessoriesAPPROVED DIRECT VENT SUPPLIERS FOR VALOR MODELS 530, 534, 535, 650, AND MF28Venting Parts Description Venting Parts Code / availa

36Venting Accessories Venting Parts DescriptionVenting Parts Code / availability by ManufacturerSIMPSON DURA-VENTSELKIRKICC EXCEL DIRECTSECURE VENT RL

37Warranty1. Extended Warranty CoverageFor a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will

38Replacement Parts123456789Description Part no. Description Part no.Black Majolica Black Majolica1 Base 4000926AH 4000926MJ 6 Fret 4000935AH 4000935M

39Description Part no. Description Part no.1 Log Set Complete 4001916 32Hooked Olive for Pilot Injector720A1962 Rear Log 4001932 33Olive Nut—Pilot Pip

4Safety & Warning InformationChildren and adults should be ALERTED to the hazards of high surface temperature and should STAY AWAY to avoid burns

123456740Replacement Parts89101150751213141617202166182265NGLPG23242725b25a28372931363233343538394042414344454647485253515449555664636262a585759603026

Thank You ...For purchasing a Valor by Miles Industries. Your new radiant gas heater is a technical appliance that must be installed by a qualifi ed de

Tape ShutThank you for choosing a Valor ProductPostageneededWere you given all documentation and manuals for your product? YES NOMiles Industries Lt

5When operating your new fi replace for the fi rst time, some vapors may be released due to the burning of curing compounds used in the manufacture of t

6Safety & Warning Information4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not a

7Specifi cationsThis appliance is certifi ed to ANSI Z21.88-2009/CSA 2.33-2009 American National Standard / CSA Standard for Vented Gas Fireplace Heater

Gas inlet position 3/8” fem.NPTxGas inlet position 3/8” fem.NPTxSupplied with top vent; fi eld convertible to rear vent8Dimensions & ClearancesInle

9Dimensions & ClearancesCorner clearances Wall clearancesMantel / shelf clearancesMin. 5” between combustible wall and stoveMin. 5” between combus